Simchair MKIV wiki

User Tools

Site Tools

Trace:
simchair4:guide_collective_body_twin-throttle

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
simchair4:guide_collective_body_twin-throttle [2019/09/22 15:26]
hc625ma 		simchair4:guide_collective_body_twin-throttle [2020/03/20 21:54] (current)
hc625ma
Line 1: Line 1:
 =======Simchair MKIV collective twin throttle lever body with tactile mark detents======= =======Simchair MKIV collective twin throttle lever body with tactile mark detents=======
  
-This manual describes the process of building a twin throttle lever body, with interchangeable heads, and a physical idle-stop detent latch. This manual was ported from the MKIII version, so you will see the MKIII collective base in the pictures: please ignore this.+This manual describes the process of building a twin throttle lever body, with interchangeable heads, and a physical idle-stop detent latch. This manual was ported from the MKIII version, so you will see the MKIII collective base in the pictures. (Please ignore this). 
 + 
 +{{http://hc625ma.org/wp-content/uploads/2018/12/IMG_20181202_215744-e1544001291605.jpg?300}}
  
 ====Components==== ====Components====
Line 7: Line 9:
   * 1 x 200x10x10mm aluminum square pipe   * 1 x 200x10x10mm aluminum square pipe
   * 1 x 105x10x10mm aluminum square pipe   * 1 x 105x10x10mm aluminum square pipe
-  * 6 x M3x30mm screws and nuts+  * 8 x M3x30mm screws and nuts
   * 1 x M3 x 35mm screw and a nut   * 1 x M3 x 35mm screw and a nut
-  * 1 x M4x80 bolts +  * 2 x M4x80 bolts 
-  * 1 x PBS-16B button+  * 2 x 16K1 linear 10K pots
  
  
Line 19: Line 21:
 ==== Assembly highlights ==== ==== Assembly highlights ====
  
-none+None.
  
 ==== Assembly Guide ==== ==== Assembly Guide ====
Line 61: Line 63:
 11.Route wires through cable channel and press-fit throttle1 p2 onto throttle 1 p1 11.Route wires through cable channel and press-fit throttle1 p2 onto throttle 1 p1
  
-{{http://hc625ma.org/wp-content/uploads/2018/12/IMG_20181201_014427-e1543675212169-768x768.jpg+{{http://hc625ma.org/wp-content/uploads/2018/12/IMG_20181201_014427-e1543675212169.jpg?300}}
  
 12. Tighten throttle 1 frame parts together with m4x80mm screw, choose a straight one 12. Tighten throttle 1 frame parts together with m4x80mm screw, choose a straight one
Line 110: Line 112:
 {{http://hc625ma.org/wp-content/uploads/2019/04/15541547885343836952077109516302.jpg?300}} {{http://hc625ma.org/wp-content/uploads/2019/04/15541547885343836952077109516302.jpg?300}}
  
-25. Put the I2C cable housing onto the lever. Use an M3x35mm screw, and secure it, in its place.+25. Put the I2C cable housing onto the lever.
  
 26. Solder the cables to your Arduino Pro Mini board, as follows: 26. Solder the cables to your Arduino Pro Mini board, as follows:
Line 121: Line 123:
     I2C HEAD CABLE SDA                   -> PRO MINI PIN A4     I2C HEAD CABLE SDA                   -> PRO MINI PIN A4
  
-27. Put the lid onto the housing and secure with 4 M8x70mm screws.+27. Put the lid onto the housing, and secure it with 4 M8x70mm screws.
  
 {{http://hc625ma.org/wp-content/uploads/2019/04/15542139378672177653029232012817.jpg?300}} {{http://hc625ma.org/wp-content/uploads/2019/04/15542139378672177653029232012817.jpg?300}}
  
-28. Make sure all the cables fit snugly inside the enclosure, and nothing touches the magnet: +28. Please check that all of the cables fit snugly inside the enclosure, and nothing touches the magnet. 
 Then you can close the hatch. Then you can close the hatch.
  
simchair4/guide_collective_body_twin-throttle.1569158776.txt.gz · Last modified: 2019/09/22 15:26 by hc625ma

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: GNU Free Documentation License 1.3
GNU Free Documentation License 1.3 Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki