simchair4_collective_base
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
simchair4_collective_base [2019/09/14 22:53] hc625ma [Assembling manual] |
— (current) | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | =======Simchair MKIV collective lever base======= | ||
| - | \\ | ||
| - | {{ http:// | ||
| - | |||
| - | {{ http:// | ||
| - | |||
| - | ====Components==== | ||
| - | |||
| - | * 1 x 10x10mm aluminum square pipe | ||
| - | * 1 x 20×10 aluminum rectangular pipe | ||
| - | * 1 x SS495A1 hall sensor | ||
| - | * 1 x MTS-103 ON-OFF-ON switch | ||
| - | * 1 x 16K1 10KOhm LINEAR rotary [[https:// | ||
| - | * 1 x 6x6x4mm square magnet | ||
| - | * 1 x M6x70mm screw | ||
| - | * 2 x M6 washers (reinforced) | ||
| - | * 1 x M6 nut | ||
| - | * 2 x M6x18x8mm hubs | ||
| - | * 6 x M4x40mm screws | ||
| - | * 4 x M4x70mm screws | ||
| - | * 1 x M3x20mm screw | ||
| - | * 1 x M3 nyloc nut | ||
| - | * 4 x M4 nyloc nuts | ||
| - | * 4 x M3x50mm screws for tensioner halves contraction | ||
| - | * 4 x M8x70 bolts | ||
| - | * 4 x M8x75mm bolts | ||
| - | * 8 x M8 nuts | ||
| - | * 10 x M8 washers (regular, non-reinforced) | ||
| - | * 4 x M8 spring washers | ||
| - | * 1 x bag of M4 nuts | ||
| - | * 4 x 608 bearings (standard skateboard bearings) | ||
| - | * 1 x Arduino Pro mini | ||
| - | * 1 x Simchair MKIV Master controller | ||
| - | * super glue (cyanoacrylate), | ||
| - | |||
| - | ====Files location in repos==== | ||
| - | |||
| - | simchair4_models\printable components\peripherals\helicopter\collective lever\a_base - models | ||
| - | |||
| - | simchair4_software\peripherals - choose the preferred variant of the lever - software | ||
| - | |||
| - | ====Assembling manual==== | ||
| - | |||
| - | 1. Insert SS495A1 into its socket in the top part of the lever frame (use a drop of super glue to fix it there) and solder its wires. Route wires as shown on the 3rd picture, use some glue as necessary. | ||
| - | |||
| - | {{ http:// | ||
| - | {{ http:// | ||
| - | {{ http:// | ||
| - | |||
| - | 2. Cut off a piece of 10mm square aluminum profile. Choose the length depending on the lever you want to build (as stated in the lever body manual, e.g. 200mm for a single throttle lever) | ||
| - | |||
| - | {{ http:// | ||
| - | |||
| - | 3. Put the lever connector part onto the rail. | ||
| - | |||
| - | {{ http:// | ||
| - | |||
| - | 4. Drill a 3mm hole through the rail and insert an M3x20mm screw with a nyloc nut. | ||
| - | |||
| - | {{ http:// | ||
| - | |||
| - | 5. Drill a 6mm hole for the axis through the rail with a 5,5mm drill. | ||
| - | |||
| - | {{ http:// | ||
| - | |||
| - | 6. We will be assembling the lever axis. Start with putting an M6x8x18mm hub onto an M6x70mm bolt. | ||
| - | |||
| - | {{ http:// | ||
| - | |||
| - | 7. Put 3 M8 washers onto the hub | ||
| - | |||
| - | {{ http:// | ||
| - | |||
| - | 8. Put 2 bearings onto the hub | ||
| - | |||
| - | {{ http:// | ||
| - | |||
| - | 9. Put a reinforced M6 nut onto the bolt | ||
| - | |||
| - | {{ http:// | ||
| - | |||
| - | 10. Put an axis though the lever connector part | ||
| - | |||
| - | {{ http:// | ||
| - | |||
| - | 11. Put a reinforced nut onto the M6 bolt. | ||
| - | |||
| - | {{ http:// | ||
| - | |||
simchair4_collective_base.1568494397.txt.gz · Last modified: 2019/09/14 22:53 by hc625ma
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: GNU Free Documentation License 1.3
