Simchair MKIV wiki

User Tools

Site Tools

Trace:
simchair4_collective_base

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
simchair4_collective_base [2019/09/14 23:19]
hc625ma [Assembling manual] 		— (current)
Line 1: Line 1:
-=======Simchair MKIV collective lever base======= 
-\\ 
-{{ http://hc625ma.org/wp-content/uploads/2019/07/IMG_20190705_112425.jpg?direct&600 |}} 
  
-{{ http://hc625ma.org/wp-content/uploads/2019/07/IMG_20190705_112438.jpg?direct&600 |}} 
- 
-====Components==== 
- 
-  * 1 x 10x10mm aluminum square pipe 
-  * 1 x 20×10 aluminum rectangular pipe 
-  * 1 x SS495A1 hall sensor 
-  * 1 x MTS-103 ON-OFF-ON switch 
-  * 1 x 16K1 10KOhm LINEAR rotary [[https://goo.gl/vbi1Zh|potentiometer]] 
-  * 1 x 6x6x4mm square magnet 
-  * 1 x M6x70mm screw 
-  * 2 x M6 washers (reinforced) 
-  * 1 x M6 nut 
-  * 2 x M6x18x8mm hubs 
-  * 6 x M4x40mm screws 
-  * 4 x M4x70mm screws 
-  * 1 x M3x20mm screw 
-  * 1 x M3 nyloc nut 
-  * 4 x M4 nyloc nuts 
-  * 4 x M3x50mm screws for tensioner halves contraction 
-  * 4 x M8x70 bolts 
-  * 4 x M8x75mm bolts 
-  * 8 x M8 nuts 
-  * 10 x M8 washers (regular, non-reinforced) 
-  * 4 x M8 spring washers 
-  * 1 x bag of M4 nuts 
-  * 4 x 608 bearings (standard skateboard bearings) 
-  * 1 x Arduino Pro mini 
-  * 1 x Simchair MKIV Master controller 
-  * super glue (cyanoacrylate), hot glue gun 
- 
-====Files location in repos==== 
- 
-simchair4_models\printable components\peripherals\helicopter\collective lever\a_base - models 
- 
-simchair4_software\peripherals - choose the preferred variant of the lever - software 
- 
-====Assembling manual==== 
- 
-1. Insert SS495A1 into its socket in the top part of the lever frame (use a drop of super glue to fix it there) and solder its wires. Route wires as shown on the 3rd picture, use some glue as necessary. 
- 
-{{ http://hc625ma.org/wp-content/uploads/2019/07/15621623810965338907647298137893.jpg?direct&600 |}} 
-{{ http://hc625ma.org/wp-content/uploads/2019/07/15621625726435977825299914770445.jpg?direct&600 |}} 
-{{ http://hc625ma.org/wp-content/uploads/2019/07/15621630944731646288145590558678.jpg?direct&600 |}} 
- 
-2. Cut off a piece of 10mm square aluminum profile. Choose the length depending on the lever you want to build (as stated in the lever body manual, e.g. 200mm for a single throttle lever) 
- 
-{{ http://hc625ma.org/wp-content/uploads/2019/07/15621646712677532393488104139149.jpg?direct&600 |}} 
- 
-3. Put the lever connector part onto the rail. 
- 
-{{ http://hc625ma.org/wp-content/uploads/2019/07/15621647541888750802542128064602.jpg?direct&600 |}} 
- 
-4. Drill a 3mm hole through the rail and insert an M3x20mm screw with a nyloc nut. 
- 
-{{ http://hc625ma.org/wp-content/uploads/2019/07/15621649112653691871033377973474.jpg?direct&600 |}} 
- 
-5. Drill a 6mm hole for the axis through the rail with a 5,5mm drill. 
- 
-{{ http://hc625ma.org/wp-content/uploads/2019/07/15621653646002757359840547887392.jpg?direct&600 |}} 
- 
-6. We will be assembling the lever axis. Start with putting an M6x8x18mm hub onto an M6x70mm bolt.  
- 
-{{ http://hc625ma.org/wp-content/uploads/2019/07/15621637378018421333394337664354.jpg?direct&600 |}} 
- 
-7. Put 3 M8 washers onto the hub 
- 
-{{ http://hc625ma.org/wp-content/uploads/2019/07/15621637939975931872903650513261.jpg?direct&600 |}} 
- 
-8. Put 2 bearings onto the hub 
- 
-{{ http://hc625ma.org/wp-content/uploads/2019/07/15621639759544702930318930238678.jpg?direct&600 |}} 
- 
-9. Put a reinforced M6 nut onto the bolt 
- 
-{{ http://hc625ma.org/wp-content/uploads/2019/07/15621642402968440300197695975340.jpg?direct&600 |}} 
- 
-10. Put an axis though the lever connector part 
- 
-{{ http://hc625ma.org/wp-content/uploads/2019/07/15621655001942847367003318010919.jpg?direct&600 |}} 
- 
-11. Put a reinforced nut onto the M6 bolt. 
- 
-{{ http://hc625ma.org/wp-content/uploads/2019/07/15621656024725412464630054854885.jpg?direct&600 |}} 
- 
-12. Put another hub onto the bolt. 
- 
-{{ http://hc625ma.org/wp-content/uploads/2019/07/15621656614566478588993330800541.jpg?direct&600 |}} 
- 
-13. Put 2 bearings onto the hub 
- 
-{{ http://hc625ma.org/wp-content/uploads/2019/07/15621658374131857828914486505264.jpg?direct&600 |}} 
- 
-14. Add 3 M8 washers 
- 
-{{ http://hc625ma.org/wp-content/uploads/2019/07/15621658862981280316395680193177.jpg?direct&600 |}} 
- 
-15. Put an M6 washer and a nut onto the bolt. Use thread locker to fix the nut. 
- 
-{{ http://hc625ma.org/wp-content/uploads/2019/07/15621662035493535529497364607651.jpg?direct&600 |}} 
- 
-16. Put the magnet onto the nut and fix it with hot glue. 
- 
-{{ http://hc625ma.org/wp-content/uploads/2019/07/15621664363831955935683107240972.jpg?direct&600 |}} 
-{{ http://hc625ma.org/wp-content/uploads/2019/07/15621667311605039704775676870956.jpg?direct&600 |}} 
- 
-17. Insert the axis assembly into its frame. 
- 
-{{ http://hc625ma.org/wp-content/uploads/2019/07/15621668167667064869085216128462.jpg?direct&600 |}} 
-{{ http://hc625ma.org/wp-content/uploads/2019/07/15621669312062702627378605380130.jpg?direct&600 |}} 
- 
-18. Insert 4 M4x40mm bolts into the frame as shown on the picture below, put nuts from the other side, use thread locker. 
- 
-{{ http://hc625ma.org/wp-content/uploads/2019/07/15621669312062702627378605380130.jpg?direct&600 |}} 
simchair4_collective_base.1568495946.txt.gz · Last modified: 2019/09/14 23:19 by hc625ma

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: GNU Free Documentation License 1.3
GNU Free Documentation License 1.3 Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki