Simchair MKIV wiki

User Tools

Site Tools

Trace:
simchair4:guide_collective_body_single-throttle-physical-idle-stop-latch

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
simchair4:guide_collective_body_single-throttle-physical-idle-stop-latch [2019/09/22 01:54]
hc625ma 		simchair4:guide_collective_body_single-throttle-physical-idle-stop-latch [2020/08/27 09:07] (current)
hc625ma
Line 10: Line 10:
   * 1 x M3 x 35mm screw and a nut   * 1 x M3 x 35mm screw and a nut
   * 1 x M4x80 bolts   * 1 x M4x80 bolts
 +  * 1 x PBS-16B button
 +  * 1 x 16K1 10KOhm LINEAR rotary potentiometer
  
  
 ==== Repository path ==== ==== Repository path ====
  
-simchair4_models\printable components\peripherals\helicopter\collective lever\b_lever bodies\single throttle +simchair4_models\printable components\peripherals\helicopter\collective lever\b_lever bodies\single throttle collective with throttle latch 
  
 ==== Assembly highlights ==== ==== Assembly highlights ====
  
-Please remember to print the latch pin using 100% infill: As at 40% infill, some users have been reporting issues with these parts breaking.+Please remember to print the latch pin using 100% infill: As at 40% infill, some users have been reporting issues with the part breaking.
  
 ==== Assembly Guide ==== ==== Assembly Guide ====
Line 77: Line 79:
 {{http://hc625ma.org/wp-content/uploads/2019/04/15541523346773794427178807155.jpg?300}} {{http://hc625ma.org/wp-content/uploads/2019/04/15541523346773794427178807155.jpg?300}}
  
-14. Disassemble the button, and take out the spring. Put the spring into the throttle latch socket.+14. Disassemble the button, and take out the spring. Insert the spring to the throttle latch socket.
  
 {{http://hc625ma.org/wp-content/uploads/2019/04/15541524871411199565383994500314.jpg?300}} {{http://hc625ma.org/wp-content/uploads/2019/04/15541524871411199565383994500314.jpg?300}}
Line 119: Line 121:
     I2C HEAD CABLE SCL                   -> PRO MINI PIN A5     I2C HEAD CABLE SCL                   -> PRO MINI PIN A5
     I2C HEAD CABLE SDA                   -> PRO MINI PIN A4     I2C HEAD CABLE SDA                   -> PRO MINI PIN A4
-     
  
-22. Flash the board using: single_collective.ino, and proceed to calibrate the lever. +22. Put the lid onto the housing and secure with 4 M8x70mm screws.
- +
-23. Now it’s a good time to do some cable management: +
- +
-{{http://hc625ma.org/wp-content/uploads/2019/04/15542134414293203651204810329367.jpg?300}} +
- +
-24. Put the lid onto the housing and secure with 4 M8x75mm screws.+
  
 {{http://hc625ma.org/wp-content/uploads/2019/04/15542139378672177653029232012817.jpg?300}} {{http://hc625ma.org/wp-content/uploads/2019/04/15542139378672177653029232012817.jpg?300}}
  
-25. Make sure all the cables fit snugly inside the enclosure, and nothing touches the magnet: +23. Make sure all the cables fit snugly inside the enclosure, and nothing touches the magnet: 
 Then you can close the hatch. Then you can close the hatch.
  
simchair4/guide_collective_body_single-throttle-physical-idle-stop-latch.1569110042.txt.gz · Last modified: 2019/09/22 01:54 by hc625ma

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: GNU Free Documentation License 1.3
GNU Free Documentation License 1.3 Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki