Simchair MKIV wiki

User Tools

Site Tools

Trace:
simchair4:guide_collective_base

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
simchair4:guide_collective_base [2019/11/04 12:19]
hc625ma [Simchair MKIV collective lever base] 		simchair4:guide_collective_base [2021/03/14 22:04] (current)
hc625ma
Line 1: Line 1:
-=======Simchair MKIV collective lever base======= +=======Simchair MKIV collective lever base classic======= 
-{{http://hc625ma.org/wp-content/uploads/2019/07/IMG_20190705_112425.jpg?400 }} +{{http://hc625ma.org/wp-content/uploads/2019/07/IMG_20190705_112425.jpg?300 }} 
-{{http://hc625ma.org/wp-content/uploads/2019/07/IMG_20190705_112438.jpg?400}}+{{http://hc625ma.org/wp-content/uploads/2019/07/IMG_20190705_112438.jpg?300}}
  
 ====Components==== ====Components====
Line 10: Line 10:
   * 1 x 6x6x4mm square magnet (or 5x5x5mm)   * 1 x 6x6x4mm square magnet (or 5x5x5mm)
   * 1 x M6x70mm screw   * 1 x M6x70mm screw
-  * 2 x M6 washers (reinforced)+  * 2 x M6 fender washers (sometimes called reinforced washers)
   * 1 x M6 nut   * 1 x M6 nut
   * 2 x M6x18x8mm hubs   * 2 x M6x18x8mm hubs
   * 6 x M4x40mm screws   * 6 x M4x40mm screws
-  * 4 x M4x70mm screws+  * 6 x M4x70mm screws (2 of them for securing devices that go into the slot on top)
   * 1 x M3x20mm screw (round head)   * 1 x M3x20mm screw (round head)
   * 1 x M3 nyloc nut   * 1 x M3 nyloc nut
Line 22: Line 22:
   * 4 x M8x75mm bolts   * 4 x M8x75mm bolts
   * 8 x M8 nuts   * 8 x M8 nuts
-  * 10 x M8 washers (regular, non-reinforced)+  * 10 x M8 washers (regular)
   * 4 x M8 spring washers   * 4 x M8 spring washers
   * 1 x bag of M4 nuts   * 1 x bag of M4 nuts
Line 29: Line 29:
   * 1 x Simchair MKIV Master controller   * 1 x Simchair MKIV Master controller
   * 2 x TJ8P8C Ethernet sockets (12,5x15x17,6mm)   * 2 x TJ8P8C Ethernet sockets (12,5x15x17,6mm)
 +  * 1 x 6*6x17 mm tactile button
   * super glue (cyanoacrylate), hot glue gun   * super glue (cyanoacrylate), hot glue gun
  
Line 79: Line 80:
 ---- ----
  
-9. Put a reinforced M6 nut onto the bolt+9. Put a reinforced M6 washer onto the bolt
 \\ {{http://hc625ma.org/wp-content/uploads/2019/07/15621642402968440300197695975340.jpg?300}} \\ {{http://hc625ma.org/wp-content/uploads/2019/07/15621642402968440300197695975340.jpg?300}}
  
 ---- ----
  
-10. Put the axis though the lever connector part+10. Put the axis though the lever connector part (orientation is important!)
 \\ {{http://hc625ma.org/wp-content/uploads/2019/07/15621655001942847367003318010919.jpg?300}} \\ {{http://hc625ma.org/wp-content/uploads/2019/07/15621655001942847367003318010919.jpg?300}}
  
Line 187: Line 188:
 ---- ----
  
-29. Solder 7-wire cables to 2 Ethernet sockets, and press-fit them into the lid.+29. Solder 7-wire cables to 2 Ethernet sockets, and press-fit them into the lid. It's best to make a cable tie and only solder a separate cable to the board so wires won't get loose and touch each other with time. Make sure you have all your VCC, GND, SCL, SDA, etc wires connected in ties and only solder 1 wire from each tie to the board for best results.
 \\ {{http://hc625ma.org/wp-content/uploads/2019/07/15622443664511173110012898373857.jpg?300}} \\ {{http://hc625ma.org/wp-content/uploads/2019/07/15622443664511173110012898373857.jpg?300}}
  
Line 193: Line 194:
  
 30. Solder wires from pins 5,6,7 of sockets to Rx, Tx, DTR pins of the board. Pay attention to cable management, and it will help you a lot! 30. Solder wires from pins 5,6,7 of sockets to Rx, Tx, DTR pins of the board. Pay attention to cable management, and it will help you a lot!
-\\ {{http://hc625ma.org/wp-content/uploads/2019/07/15622447963579198439391455829393.jpg?300 }}+\\ {{http://hc625ma.org/wiki/lib/exe/fetch.php?media=simchair4:rj45-pin-numbers.jpg?600}} 
 + 
 +  PIN5 -> Rx 
 +  PIN6 -> Tx 
 +  PIN7 -> DTR 
 + 
 +{{http://hc625ma.org/wp-content/uploads/2019/07/15622447963579198439391455829393.jpg?300 }}
 {{http://hc625ma.org/wp-content/uploads/2019/07/15622452733241440425178470616604.jpg?300}} {{http://hc625ma.org/wp-content/uploads/2019/07/15622452733241440425178470616604.jpg?300}}
  
Line 205: Line 212:
 ---- ----
  
-32. Connect the I2C cable to VCC,GND,SCL(A5),SDA(A4) +32. Connect the I2C cable to VCC,GND,SCL(A5),SDA(A4) as follows: 
-\\ {{http://hc625ma.org/wp-content/uploads/2019/07/15622460864528809517621917146166.jpg?300 }}+\\  
 +{{http://hc625ma.org/wiki/lib/exe/fetch.php?media=simchair4:rj45-pin-numbers.jpg?600}} 
 + 
 +  PIN1 -> VCC 
 +  PIN2 -> GND 
 +  PIN3 ->SCL (A5) 
 +  PIN4 -> SDA(A4) 
 + 
 +{{http://hc625ma.org/wp-content/uploads/2019/07/15622460864528809517621917146166.jpg?300 }}
 {{http://hc625ma.org/wp-content/uploads/2019/07/15622466991834160676435414207670.jpg?300}} {{http://hc625ma.org/wp-content/uploads/2019/07/15622466991834160676435414207670.jpg?300}}
  
Line 233: Line 248:
   * A0 -> SS495A1 signal   * A0 -> SS495A1 signal
   * A1 -> THR POT signal   * A1 -> THR POT signal
-  * A4 -> SDA cable tie <- Ethernet sockets pin 3 +  * A5 -> SCL cable tie <- Ethernet sockets pin 3 
-  * A5 -> SCL cable tie <- Ethernet sockets pin 4+  * A4 -> SDA cable tie <- Ethernet sockets pin 4
   * Collective head I2C cable -> VCC, GND, SCL,SDA cable ties   * Collective head I2C cable -> VCC, GND, SCL,SDA cable ties
   * Pro Mini Rx -> Ethernet sockets pin 5   * Pro Mini Rx -> Ethernet sockets pin 5
simchair4/guide_collective_base.1572866340.txt.gz · Last modified: 2019/11/04 12:19 by hc625ma

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: GNU Free Documentation License 1.3
GNU Free Documentation License 1.3 Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki