This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
simchair4:guide_collective_head_b206 [2019/10/14 23:34] hc625ma |
simchair4:guide_collective_head_b206 [2019/11/02 21:21] (current) rfvizarra [Components] |
||
---|---|---|---|
Line 4: | Line 4: | ||
===== Summary ===== | ===== Summary ===== | ||
- | This is a scale Bell 206 collective head! It's made using photos with measurements, | + | This is a scale Bell 206 collective head! It's made using photos with measurements, |
{{: | {{: | ||
- | |||
- | |||
- | |||
===== Components ===== | ===== Components ===== | ||
Line 17: | Line 14: | ||
* 1 x PBS-10B2 button | * 1 x PBS-10B2 button | ||
* 3 x M3x40mm countersunk screws and nuts | * 3 x M3x40mm countersunk screws and nuts | ||
+ | * 1 x M3x35mm round head screw and nut | ||
* 1 x Arduino Pro Mini | * 1 x Arduino Pro Mini | ||
+ | * 1 x TJ8P8C Ethernet sockets (12, | ||
===== Repository path ===== | ===== Repository path ===== | ||
Line 26: | Line 25: | ||
* print small parts at the highest quality setting and 0,1mm layer height | * print small parts at the highest quality setting and 0,1mm layer height | ||
- | * if you want the version of the panel with letters - print it at 0,1mm as well, adjust the number of layers on top to 5 or 6 | + | * if you want the version of the panel with letters - print it at 0,1mm as well, adjust the number of layers on top to 5 or 6; use layer width equal the width of your nozzle! |
- | * use a correction white marker to fill letters with white paint, and then carefully paint them over with a black permanent marker (it wont be filling letters!), then paint the rest of the panel with it for colors to match. | + | * use a correction white marker to fill letters with white paint, and then carefully paint them over with a black permanent marker (it won' |
===== Assembly guide ===== | ===== Assembly guide ===== | ||
- | 1. Prepare the top panel of choice and insert switches in it. Cut the top off the MTS-123-E1 plastic cap so the scale cap will fit onto it. You can use a black marker to paint the cap if its not black. Insert the PBS button into its socket, glue the decorative cover on top of it and then put the scale cap on. | + | 1. Prepare the top panel of choice and insert switches in it. Cut the top off the MTS-123-E1 plastic cap so the scale cap will fit onto it. You can use a black marker to paint the cap if it' |
{{: | {{: | ||
Line 40: | Line 39: | ||
{{: | {{: | ||
- | 3. Solder an ISP header to Arduino Pro Mini board. | + | 3. Solder an ISP header to Arduino Pro Mini board. |
- | 4. Solder a 5-wire cable to switches as follows: | + | ETH SOCKET PIN 1 => VCC |
+ | ETH SOCKET PIN 2 => GND | ||
+ | ETH SOCKET PIN 3 => SCL (A5) | ||
+ | ETH SOCKET PIN 4 => SDA (A4) | ||
+ | ETH SOCKET PIN 5 => Rx | ||
+ | ETH SOCKET PIN 6 => Tx | ||
+ | ETH SOCKET PIN 7 => DTR | ||
- | LDG LTS SW BOTH SIDE-> PIN2 | + | {{: |
- | LDG LTS SW OFF SIDE -> PIN3 | + | |
- | GOV RPM INCR SIDE -> PIN4 | + | |
- | GOV RPM DECR SIDE -> PIN5 | + | |
- | STARTER BTN -> PIN6 | + | |
- | {{:simchair4: | + | 4. Solder a 5-wire cable to switches as follows (numbers on the pic correspond to Arduino pin numbers): |
- | 5. Solder a 7-wire cable to an Ethernet socket. Connect it as follows: | + | {{:simchair4: |
- | ETH PIN 1 => VCC | ||
- | ETH PIN 2 => GND | ||
- | ETH PIN 3 => SCL | ||
- | ETH PIN 4 => SDA | ||
- | ETH PIN 5 => Rx | ||
- | ETH PIN 6 => TX | ||
- | ETH PIN 7 => DTR | ||
- | {{: | + | LDG LTS SW BOTH SIDE (2) -> PRO MINI PIN2 |
+ | LDG LTS SW OFF SIDE (3) -> PRO MINI PIN3 | ||
+ | GOV RPM INCR SIDE (4) -> PRO MINI PIN4 | ||
+ | GOV RPM DECR SIDE (5) -> PRO MINI PIN5 | ||
+ | STARTER BTN (6) -> PRO MINI PIN6 | ||
+ | |||
+ | Put a piece of shrink tube onto the board and do some cable management. | ||
+ | |||
+ | {{: | ||
+ | {{: | ||
+ | {{: | ||
+ | |||
+ | 5. Flash the head with its firmware, uncomment it in the " | ||
+ | |||
+ | 6. Put everything into the box, do some cable management so that the aluminum pipe won't damage wires when the head will be put onto the lever. Push onto the Ethernet socket so it will protrude slightly from the bottom. Glue the socket cap part with some cyanoacrylate and level the socket with it so it will look good. Carefully fix the socket in place with hot glue. | ||
+ | |||
+ | {{: | ||
+ | {{: | ||
+ | {{: | ||
+ | {{: | ||
+ | {{: | ||
- | {{: | + | That's it, time to do some flying! =) |