This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
simchair4:guide_collective_head_uh-1 [2019/09/21 22:39] retrogamer |
simchair4:guide_collective_head_uh-1 [2024/03/30 08:44] (current) retrogamer addition |
||
---|---|---|---|
Line 70: | Line 70: | ||
---- | ---- | ||
- | 5. Cut a wire off the ribbon cable, and connect ground (middle) pins of the switches and the button together, as shown on picture. | + | 5. Cut a wire off the ribbon cable, and connect ground (middle) pins of the switches and the button together, as shown on the picture |
\\ {{http:// | \\ {{http:// | ||
---- | ---- | ||
- | 6. Cut a 12-wire cable off the ribbon. Solder wires one by one, following numbers on the picture. The last wire will be the ground one. Use the same contact pads row where the ground wire is. | + | 6. Cut a 12-wire cable off the ribbon. Solder wires one by one, following numbers on the picture. The last wire will be the ground one. Use the same contact pads row, where the ground wire is. |
- | \\ {{http:// | + | \\ {{:simchair4: |
---- | ---- | ||
- | 7. Fix with hot glue so it won’t move. | + | 7. Apply enough |
\\ {{http:// | \\ {{http:// | ||
---- | ---- | ||
- | 8. Solder 5-wire cable, cut off the ribbon, to the pot board. Put it onto its frame, fix with 4x M3x10MM screws. | + | 8. Solder |
\\ {{http:// | \\ {{http:// | ||
Line 95: | Line 95: | ||
---- | ---- | ||
- | 10. Starting from pin0, solder the 12-wire switches cable to Pro Mini’s digital pins. The wire of the button should go to pin10, and the last wire of the cable should go to the GND pin near it. | + | 10. Starting from pin0, solder the 12-wire switches cable to the Pro Mini’s digital pins. The wire of the button should go to pin10, and the last wire of the cable should go to the GND pin, near it. |
\\ {{http:// | \\ {{http:// | ||
{{http:// | {{http:// | ||
Line 101: | Line 101: | ||
---- | ---- | ||
- | 11. Bend legs of PBS-10B2 button as shown on picture and solder long enough wires to it, then insert it into its socket in the lower part of the housing, fix with its nut (rotate it with pliers or a knife, tighten | + | 11. Bend the legs of PBS-10B2 button, as shown on picture, and solder long enough wires to it. Then insert it into its socket in the lower part of the housing. Fix with it' |
\\ {{http:// | \\ {{http:// | ||
{{http:// | {{http:// | ||
Line 107: | Line 107: | ||
---- | ---- | ||
- | 12. Solder 4-wire cable to 1st 4 pins of an Ethernet socket. | + | 12. Solder |
\\ {{http:// | \\ {{http:// | ||
Line 113: | Line 113: | ||
13. Press-fit the socket into its slot and check that wires are still connected to the socket with a multimeter. | 13. Press-fit the socket into its slot and check that wires are still connected to the socket with a multimeter. | ||
+ | |||
+ | To make the installation easier: | ||
+ | |||
+ | - Make sure the pins and cables are bent rather flat, so that you have the clearance to slide the socket to its place from the inside. | ||
+ | |||
+ | - Use a screwdriver or similar to apply force and push the socket thru the opening, in the end. | ||
+ | |||
+ | - Applying the hot glue might get tricky, as the crevice is small, use of a tool might be a good idea. | ||
+ | |||
\\ {{http:// | \\ {{http:// | ||
{{http:// | {{http:// | ||
Line 138: | Line 147: | ||
* SOCKET PIN3 -> SCL (A5) | * SOCKET PIN3 -> SCL (A5) | ||
* SOCKET PIN4 -> SDA (A4) | * SOCKET PIN4 -> SDA (A4) | ||
+ | * SOCKET PIN5 -> Rx | ||
+ | * SOCKET PIN6 -> Tx | ||
+ | * SOCKET PIN7 -> DTR | ||
\\ {{http:// | \\ {{http:// | ||
Line 155: | Line 167: | ||
---- | ---- | ||
- | 19. When you have checked all switches and buttons, comment out “Serial.begin” | + | 19. When you have checked all switches and buttons, |
'' | '' | ||
Line 165: | Line 177: | ||
---- | ---- | ||
- | 21. Insert the starter trigger and fix it with an M3x30mm screw. Drill out its hole if needed | + | 21. Insert the starter trigger, and fix it with an M3x30mm screw. Drill out it' |
\\ {{http:// | \\ {{http:// | ||