Differences

This shows you the differences between two versions of the page.

--- simchair4:guide_cyclic_grip-b8 [2019/10/29 21:56]
hc625ma
+++ simchair4:guide_cyclic_grip-b8 [2021/01/22 20:16] (current)
hc625ma
@@ Line 13: / Line 13: @@
   * 1 x Arduino pro mini board
   * 1 x KY-023 joystick module
-  * 1 x USBtoCOM adapter (e.g., PL2303) or another Arduino to program it
   * 3 x PBS-11B buttons
   * 1 x PBS-10B-2 button (trigger intercom)
   * 1 x 12x12x4.3mm TS-1202 button (https://goo.gl/mjpt6T) (trigger PTT)
   * some wires
-  * 1 x m8 x 60 bolt and nut
+  * 1 x M8 x 60 bolt and nut
   * 1m of UTP-5e cable
   * 1m of 10mm aluminum square pipe
@@ Line 24: / Line 23: @@
   * 1 x m3x40 screw for trigger mounting
-  * 1 x Simchair MKIII I2C controller (Arduino Leonardo based) (https://www.thingiverse.com/thing:2919692)
+  * 1 x Simchair MKIV master controller
-  * 1 x Simchair MKIII cyclic gimbal V2 (https://www.thingiverse.com/thing:2917209)
+  * 1 x Simchair MKIV cyclic base
   * Hot glue gun
 =====Repository path=====
-[[https://github.com/hc625ma/simchair_models/tree/master/Components/Peripherals/B8%20flight%20stick|simchair_models/tree/master/Components/Peripherals/B8 flight stick]]
+[[https://github.com/hc625ma/simchair4_models/tree/master/printable%20components/peripherals/helicopter/cyclic%20lever/b_grips/B8%20flight%20stick]]
 =====Available mods=====
@@ Line 101: / Line 100: @@
 Connect buttons and the pot board to an Arduino as follows:
-  POT BOARD VCC            -> PIN 10 \\
+  POT BOARD VCC            -> PIN 10
-  POT BOARD GND            -> Arduino GND\\
+  POT BOARD GND            -> Arduino GND
-  POT VRx                  -> A0\\
+  POT VRx                  -> A0
-  POT VRy                  -> A1\\
+  POT VRy                  -> A1
-  POT BOARD BUTTON         –> PIN 2\\
+  POT BOARD BUTTON         –> PIN 2
-  TOP BTN (TRIMMER)        –> between PIN 3 and GND\\
+  TOP BTN (TRIMMER)        –> between PIN 3 and GND
-  MIDDLE BTN(FIRE)         –> between PIN 4 and GND\\
+  MIDDLE BTN(FIRE)         –> between PIN 4 and GND
-  BOTTOM BTN               –> between PIN 5 and GND\\
+  BOTTOM BTN               –> between PIN 5 and GND
-  TRIGGER INTERCOM         –> between PIN 6 and GND\\
+  TRIGGER INTERCOM         –> between PIN 6 and GND
-  TRIGGER PTT (full press) –> between PIN 7 and GND\\
+  TRIGGER PTT (full press) –> between PIN 7 and GND
-  A4  (SDA)                -> ethernet cable blue wire\\
+  A4(SDA)                  -> ethernet cable blue wire
-  A5  (SCL)                -> ethernet cable green-white wire\\
+  A5(SCL)                  -> ethernet cable green-white wire
-  VCC                      -> ethernet cable orange-white wire\\
+  VCC                      -> ethernet cable orange-white wire
-  GND                      -> ethernet cable orange wire\\
+  GND                      -> ethernet cable orange wire
-  Rx                       -> ethernet cable blue=white wire\\
+  Rx                       -> ethernet cable blue=white wire
-  Tx                       -> ethernet cable green wire\\
+  Tx                       -> ethernet cable green wire
   DTR                      -> ethernet cable brown-white wire
 {{http://hc625ma.org/wp-content/uploads/2018/05/photo-300x188.gif}}
-After soldering everything, put the Pro mini board into its socket, organize wires, put an M8x75 bolt with a nut into its place, and finally screw the halves together.
+After soldering everything, put the Pro Mini board into its socket, organize wires, put an M8x75 bolt with a nut into its place, and finally screw the halves together.

Simchair MKIV wiki

User Tools

Site Tools

Differences

Page Tools