Differences

This shows you the differences between two versions of the page.

--- simchair4:guide_collective_pedestal_simple [2019/09/21 21:04]
hc625ma
+++ simchair4:guide_collective_pedestal_simple [2020/02/12 21:18] (current)
hc625ma
@@ Line 2: / Line 2: @@
 ===== About Pedestals =====
-A pedestal is a device that is mounted onto the collective base to extend its functionality. A few of them are currently available under the MKIV line of hardware. \\ The recommended default option for flying in VR is a simple pedestal. If you use radios often, try [[http://hc625ma.org/wiki/doku.php?id=simchair4:guide_pedestal_vrmax_2|VRMax II]] one instead.
+A pedestal is a device that is mounted onto the collective base to extend its functionality. A few of them are currently available under the MKIV line of hardware. \\ The recommended default option for flying in VR, is the simple pedestal. If you use radios often, please try this one instead: [[http://hc625ma.org/wiki/doku.php?id=simchair4:guide_pedestal_vrmax_2|VRMax II]]
 \\ {{http://hc625ma.org/wp-content/uploads/2019/07/15627830635082538391043702422025-1024x1024.jpg?100 |Simple Pedestal}} {{http://hc625ma.org/wp-content/uploads/2019/08/IMG_20190805_000943-1024x1024.jpg?100|VRMaxII Pedestal}}
 ===== Summary =====
-The Simple Pedestal for the MKIV collective base is a universal VR mouse replacement device, that will make your flying experience much better in a simple way. \\ It features a single **knob emulating the mousewheel** and a **ministick to control a cursor** – that means __you can control any knob in the cockpit__ no matter how many of them are there. That also means that you can use your left hand to comfortably operate switches and radios while flying.
+The Simple Pedestal for the MKIV collective base is a universal VR mouse replacement device.
+It will make your flying experience much better in a simple way. \\ It features a single **knob, emulating the mousewheel** and a **ministick, to control the cursor** – This means that __you can control any knob in the cockpit__ no matter how many of them are there. This also means that you can use your left hand to comfortably operate switches and radios during the flight.
-I’ve tried it, and i can say that seriously, this thing is simply epic, and is definitely one of the highlights of the MKIV line. \\ {{http://hc625ma.org/wp-content/uploads/2019/07/15627830635082538391043702422025-1024x1024.jpg?300 |}}
+I’ve tried it, and i can say that seriously, this thing is simply epic, and it is definitely one of the highlights of the MKIV line. \\ {{http://hc625ma.org/wp-content/uploads/2019/07/15627830635082538391043702422025-1024x1024.jpg?300 |}}
 {{http://hc625ma.org/wp-content/uploads/2019/07/15627830305946399886825033053157-1024x1024.jpg?300}}
@@ Line 18: / Line 19: @@
   * 1 x PEC16-4220F-S0024 encoder
   * 2 x PBS-10B2 buttons
+  * 1 x 6x6x5mm tact button
   * 1 x KY-023 ministick board
   * 1 x Bourns PTD901-2015K-B103 10K resistor
   * 1 x TJ8P8C Ethernet socket
   * 4 x M3x35mm screws and nuts
+  * 4 x M3x10m screws to fix the KY board
   * 1 x Arduino Pro Mini
@@ Line 72: / Line 75: @@
 ----
-. Solder the ground wire to all switches and buttons, including the encoder.
+. Solder the ground wire to all switches and buttons, including 2 pins (one of two pins at the bottom and the middle pin at the top) of the encoder. **Note that there's an error on the 1st pic - the GND wire of the pot should be soldered as shown on pic 3!**
 \\ {{http://hc625ma.org/wp-content/uploads/2019/07/15627730836328300368345058106497-1024x1024.jpg?300 }}
 {{http://hc625ma.org/wp-content/uploads/2019/07/15627769037866535624841868767739-1024x1024.jpg?300}}
@@ Line 124: / Line 127: @@
 ----
-. Check that everything looks correct. Flash the board with the firmware using a FT232TL based adapter (or any other) and a UART- Ethernet cable. Connect it to the master controller and check that everything works. If everthing is ok, proceed, otherwise go back, and check your connections, and that the LED on pin 13 really was removed!
+. Check that everything looks correct. Flash the board with the firmware using a FT232TL based adapter (or any other) and a UART- Ethernet cable. Connect it to the master controller and check that everything works. If everthing is ok, proceed, otherwise go back, and check your connections, and that the LED on pin 13, was really removed!
 ----
-. Close the lid, fix with 4 M3x35mm sxrews, put knobs on. When attaching the zoom axis knob, center the pot as shown on the pic below.
+. Close the lid. Fix it with 4 M3x35mm sxrews, put the knobs on. When attaching the zoom axis knob, center the pot as shown on the picture below:
 \\ {{http://hc625ma.org/wp-content/uploads/2019/07/15627816433331658451582558076678-1024x1024.jpg?300 }}
 {{http://hc625ma.org/wp-content/uploads/2019/07/15627817491931262949557222847434-1024x1024.jpg?300}}
@@ Line 134: / Line 137: @@
 ----
-. Calibrate the ministick, to do it, uncomment the following lines in the ''**//g_simple_pedestal//**'' tab of ''**a_master.ino**'' (master controller sketch):
+. Calibrate the ministick: To do this, uncomment the following lines in the ''**//g_simple_pedestal//**'' tab of ''**a_master.ino**'' (master controller sketch):
 <code>Serial.print(x);
 Serial.print(" ");

Simchair MKIV wiki

User Tools

Site Tools

Differences

Page Tools