Simchair MKIV wiki

User Tools

Site Tools

Trace: • guide_master_controller
simchair4:guide_collective_pedestal_simple

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
simchair4:guide_collective_pedestal_simple [2019/09/21 21:19]
retrogamer 		simchair4:guide_collective_pedestal_simple [2020/02/12 21:18] (current)
hc625ma
Line 10: Line 10:
 It will make your flying experience much better in a simple way. \\ It features a single **knob, emulating the mousewheel** and a **ministick, to control the cursor** – This means that __you can control any knob in the cockpit__ no matter how many of them are there. This also means that you can use your left hand to comfortably operate switches and radios during the flight. It will make your flying experience much better in a simple way. \\ It features a single **knob, emulating the mousewheel** and a **ministick, to control the cursor** – This means that __you can control any knob in the cockpit__ no matter how many of them are there. This also means that you can use your left hand to comfortably operate switches and radios during the flight.
  
-I’ve tried it, and i can say that seriously, this thing is simply epic, and is definitely one of the highlights of the MKIV line. \\ {{http://hc625ma.org/wp-content/uploads/2019/07/15627830635082538391043702422025-1024x1024.jpg?300 |}}+I’ve tried it, and i can say that seriously, this thing is simply epic, and it is definitely one of the highlights of the MKIV line. \\ {{http://hc625ma.org/wp-content/uploads/2019/07/15627830635082538391043702422025-1024x1024.jpg?300 |}}
 {{http://hc625ma.org/wp-content/uploads/2019/07/15627830305946399886825033053157-1024x1024.jpg?300}} {{http://hc625ma.org/wp-content/uploads/2019/07/15627830305946399886825033053157-1024x1024.jpg?300}}
  
Line 19: Line 19:
   * 1 x PEC16-4220F-S0024 encoder   * 1 x PEC16-4220F-S0024 encoder
   * 2 x PBS-10B2 buttons   * 2 x PBS-10B2 buttons
 +  * 1 x 6x6x5mm tact button
   * 1 x KY-023 ministick board   * 1 x KY-023 ministick board
   * 1 x Bourns PTD901-2015K-B103 10K resistor   * 1 x Bourns PTD901-2015K-B103 10K resistor
   * 1 x TJ8P8C Ethernet socket   * 1 x TJ8P8C Ethernet socket
   * 4 x M3x35mm screws and nuts   * 4 x M3x35mm screws and nuts
 +  * 4 x M3x10m screws to fix the KY board
   * 1 x Arduino Pro Mini   * 1 x Arduino Pro Mini
  
Line 73: Line 75:
 ---- ----
  
-7. Solder the ground wire to all switches and buttons, including the encoder.+7. Solder the ground wire to all switches and buttons, including 2 pins (one of two pins at the bottom and the middle pin at the top) of the encoder. **Note that there's an error on the 1st pic - the GND wire of the pot should be soldered as shown on pic 3!**
 \\ {{http://hc625ma.org/wp-content/uploads/2019/07/15627730836328300368345058106497-1024x1024.jpg?300 }} \\ {{http://hc625ma.org/wp-content/uploads/2019/07/15627730836328300368345058106497-1024x1024.jpg?300 }}
 {{http://hc625ma.org/wp-content/uploads/2019/07/15627769037866535624841868767739-1024x1024.jpg?300}} {{http://hc625ma.org/wp-content/uploads/2019/07/15627769037866535624841868767739-1024x1024.jpg?300}}
simchair4/guide_collective_pedestal_simple.1569093558.txt.gz · Last modified: 2019/09/21 21:19 by retrogamer

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: GNU Free Documentation License 1.3
GNU Free Documentation License 1.3 Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki